Rex Sewing Machine Manual

The Rex Sewing Machine is a versatile household sewing device with multiple stitch patterns, adjustable stitch length and width, built-in needle threader, free arm capability, automatic bobbin winding, built-in LED light, and variable speed control. Powered by 120V AC, 60Hz. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Sewing head with built-in LED light, Free arm, Stitch selection dial, Bobbin winder, Foot pedal, Power cord, Accessory compartment.

Installation

Unpack and inspect contents. Place on stable surface.

1. Remove machine from packaging: Carefully lift machine from box.
2. Attach foot pedal: Connect foot pedal to machine port.
3. Connect power: Plug power cord into machine and wall outlet.
4. Install accessories: Place accessory box in compartment.

WARNING! Machine is heavy; lift with care to avoid injury. Ensure stable placement.

First-Time Setup

Power on machine; follow setup procedures.

1. Thread machine: Follow threading guide printed on machine.
2. Wind bobbin: Place empty bobbin on winder and follow winding procedure.
3. Insert bobbin: Place wound bobbin in bobbin case following diagram.
4. Test stitches: Select straight stitch and test on scrap fabric.

CAUTION! Keep fingers away from needle area during operation.

Specifications

• Machine Type: Electronic household sewing machine
• Stitch Patterns: 23 built-in stitches
• Stitch Length: 0-4mm adjustable
• Stitch Width: 0-5mm adjustable
• Speed Control: Variable via foot pedal
• Lighting: Built-in LED light
• Bobbin: Front loading, class 15 transparent
• Needle: Standard domestic needles
• Power Source: 120V AC, 60Hz
• Weight: 12 lbs

Controls and Settings

Main controls located on front and side of machine.

Front Panel: Stitch selection dial, Stitch length control, Stitch width control, Reverse stitch button, Power switch.

Stitch Selection: Turn dial to select desired stitch pattern. Stitch Length: Adjust for shorter or longer stitches. Stitch Width: Adjust for narrow or wide zigzag. Reverse: Hold button for backstitching. Tension: Adjust thread tension dial (4-6 for normal sewing).

Connecting Accessories

Various presser feet and accessories included.

1. Attach presser foot: Lift lever, position foot, lower lever.
2. Change needles: Loosen needle clamp screw, insert new needle.
3. Connect extension table: Snap into place for larger sewing area.
4. Install specialty feet: Zigzag foot, zipper foot, buttonhole foot.

Tip: Always turn power off when changing accessories.

Basic Sewing Operations

Follow these steps for basic sewing tasks.

1. Thread machine: Follow numbered threading path.
2. Select stitch: Turn dial to desired pattern.
3. Position fabric: Lower presser foot over fabric.
4. Start sewing: Press foot pedal gently to begin.
5. Guide fabric: Let machine feed fabric; do not pull.
6. Reverse stitch: Hold reverse button at start and end.
7. Finish: Raise needle, lift presser foot, remove fabric.
8. Cut threads: Use built-in thread cutter.

WARNING! Never sew over pins; remove them as you sew.

Maintenance & Care

Regular maintenance ensures optimal performance.

1. Clean lint: Remove bobbin case and clean lint regularly.
2. Oil machine: Apply sewing machine oil as indicated in diagram.
3. Change needles: Replace needle after 8-10 hours of sewing.
4. Store properly: Cover machine when not in use.

CAUTION! Unplug machine before cleaning or maintenance.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © 2025 Rex Sewing Machines; all rights reserved. For support, visit www.rexsewing.com or contact 1-800-555-REX.

Troubleshooting

Reset: Turn machine off and on if electronic issues occur.

Service: 1-800-555-REX; www.rexsewing.com