janome sewing machine model 802 manual

The Janome Sewing Machine Model 802 is a versatile mechanical sewing machine designed for home use, featuring straight stitch, zigzag stitch, and buttonhole capabilities. With built-in stitch patterns, adjustable stitch length and width, free arm design, built-in needle threader, top drop-in bobbin system, and multiple presser feet included. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Mechanical sewing machine with built-in stitches, free arm, built-in needle threader, top loading bobbin, and multiple presser feet.

Installation & Setup

Unpack and inspect all contents. Place on stable sewing table.

1. Remove packaging materials and protective covers from machine.
2. Place machine on flat, stable surface at comfortable working height.
3. Connect foot pedal to machine and plug into power outlet.
4. Install needle properly with flat side facing back.
5. Wind and insert bobbin following threading diagram.

WARNING! Keep fingers away from needle area during operation. Always turn off when not in use.

First-Time Operation

Power on machine; follow threading instructions.

1. Thread upper thread: Follow numbered threading path on machine.
2. Insert bobbin: Place bobbin in case with thread unwinding counterclockwise.
3. Raise needle to highest position using handwheel.
4. Select straight stitch pattern for initial testing.
5. Place fabric under presser foot and lower foot lever.
6. Gently press foot pedal to begin sewing.

CAUTION! Always start with scrap fabric to test stitches and tension.

Specifications

• Machine Type: Mechanical sewing machine
• Built-in Stitches: 8 stitches including straight, zigzag, and decorative
• Stitch Length: 0-4mm adjustable
• Stitch Width: 0-5mm adjustable for zigzag
• Buttonhole: 4-step buttonhole
• Bobbin System: Top drop-in bobbin
• Needle System: HA-1 needle system
• Free Arm: Yes, for sewing sleeves and cuffs
• Power Requirements: 110-120V, 60Hz
• Weight: Approximately 11 lbs (5 kg)

Controls and Settings

Main controls located on front and side of machine.

Stitch Selection: Turn dial to select desired stitch pattern. Stitch Length: Adjust with lever (0-4mm). Stitch Width: Adjust with dial (0-5mm for zigzag). Reverse Stitch: Press and hold button for reinforcement. Handwheel: Turn toward you to manually raise/lower needle.

Tension Control: Adjust upper thread tension (3-5 for normal fabrics). Presser Foot Pressure: Spring-loaded for most fabrics. Feed Dogs: Drop for free-motion sewing or button sewing.

Stitch Selection

8 built-in stitch patterns available:

1. Straight stitch - for basic sewing
2. Zigzag stitch - for finishing edges
3. 3-step zigzag - for stretch fabrics
4. Blind hem stitch - for invisible hems
5. Shell stitch - decorative edge finish
6. Multiple stitch - decorative pattern
7. Elastic stitch - for elastic application
8. Buttonhole stitch - 4-step buttonhole

Tip: Always test stitch on scrap fabric before sewing project.

Threading & Bobbin

Proper threading ensures smooth operation.

1. Raise presser foot and raise needle to highest position.
2. Place spool on spool pin and follow numbered threading path.
3. Use built-in needle threader for easy needle threading.
4. Wind bobbin with same thread as upper thread.
5. Insert bobbin with thread unwinding counterclockwise.
6. Pull bobbin thread up through needle plate.

WARNING! Ensure machine is turned off during threading.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

1. Clean lint from bobbin area after each project.
2. Oil machine as indicated in manual (specific points only).
3. Replace needle regularly (every 8-10 hours of sewing).
4. Keep machine covered when not in use.
5. Use only Janome recommended needles and accessories.

CAUTION! Unplug machine before cleaning or maintenance.

Accessories Included

Standard accessories with Model 802:

• All-purpose foot
• Zipper foot
• Buttonhole foot
• Button sewing foot
• Bobbin (x4)
• Needles (x3)
• Seam ripper/lint brush
• Screwdriver
• Spool cap (large and small)
• Instruction manual

Warranty Information

Janome Model 802 comes with 25-year limited warranty. Warranty covers manufacturing defects in materials and workmanship. Normal wear items (needles, belts, light bulbs) not covered. For warranty service, contact authorized Janome dealer with proof of purchase. Keep original packaging for 30 days.

Troubleshooting

Service: Contact authorized Janome dealer for repairs. Customer service: 1-800-631-0183