Janome Sewing Machine Manual 1008

The Janome Sewing Machine Model 1008 is a mechanical sewing machine designed for home use, featuring 8 built-in stitches, 4-step buttonhole function, drop feed for free-motion sewing, built-in needle threader, stitch length and width adjustment, reverse sewing, and built-in thread cutter. Powered by 120V AC, 60Hz. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Setup 3. First-Time Operation 4. Specifications 5. Controls and Settings 6. Stitch Selection 7. Basic Sewing Operations 8. Maintenance & Cleaning 9. Safety Information 10. Troubleshooting

Features at a Glance

Key components: Mechanical sewing machine with 8 built-in stitches, stitch selection dial, stitch length control, stitch width control, reverse lever, built-in needle threader, drop feed lever, and free arm design.

FeatureDescription
Built-in stitches8 utility stitches including straight, zigzag, and stretch stitches
4-step buttonholeEasy buttonhole creation in 4 simple steps
Drop feedLower feed dogs for free-motion sewing and darning
Built-in needle threaderAutomatic needle threading for easy setup
Stitch length controlAdjustable stitch length from 0-4mm
Stitch width controlAdjustable stitch width up to 5mm
Reverse sewing leverReinforce stitches at beginning and end of seams
Free armRemovable extension table for sewing cuffs and sleeves
Built-in thread cutterConvenient thread cutting on the machine
Bobbin systemFront-loading bobbin with clear cover

Installation & Setup

Unpack and inspect contents. Place on stable surface at comfortable working height.

  1. Remove machine from packaging: Lift machine by base, not handwheel.
  2. Attach extension table: Slide into position until it clicks.
  3. Install foot controller: Plug into machine and position on floor.
  4. Connect power: Plug power cord into machine and wall outlet.
  5. Wind bobbin: Follow bobbin winding instructions.
  6. Thread machine: Follow threading diagram on machine.

WARNING! Machine is heavy; lift with care using both hands. Ensure stable work surface.

First-Time Operation

Power on machine; test basic functions before sewing projects.

  1. Select straight stitch: Turn stitch selection dial to straight stitch position.
  2. Set stitch length: Adjust to medium setting (2.5-3.0).
  3. Thread machine: Follow numbered threading path.
  4. Insert bobbin: Ensure bobbin rotates counterclockwise when pulled.
  5. Test sew: Use scrap fabric to test stitching.
  6. Adjust tension: Check both top and bobbin thread tension.

CAUTION! Keep fingers away from needle area during operation. Always turn off when not in use.

Specifications

Controls and Settings

Main controls located on front and side of machine. Stitch Selection Dial: Rotate to select desired stitch pattern. Stitch Length Dial: Adjust from 0 (darning) to 4 (basting). Stitch Width Dial: Adjust zigzag width from 0-5mm.

Additional Controls: Reverse Sewing Lever, Drop Feed Lever, Handwheel, Foot Controller, Power Switch, Light Switch.

Thread Tension: Adjust top thread tension dial (0-9). Bobbin Tension: Factory set; adjust only if necessary. Presser Foot Pressure: Adjustable for different fabric types.

Stitch Selection

8 built-in stitches for various sewing applications:

  1. Straight Stitch: Basic sewing, topstitching (center needle position)
  2. Zigzag Stitch: Finishing edges, appliqué, decorative work
  3. Multiple Zigzag: Elastic application, mending
  4. Blind Hem Stitch: Nearly invisible hems
  5. Stretch Stitches: For knit and stretch fabrics
  6. Decorative Stitches: Simple decorative patterns
  7. Buttonhole Stitch: Step 1 of 4-step buttonhole
  8. Satin Stitch: Close zigzag for appliqué and monograms

Tip: Always test stitch on scrap fabric before sewing project.

Basic Sewing Operations

Follow these steps for successful sewing:

  1. Raise needle to highest position using handwheel.
  2. Raise presser foot and place fabric under foot.
  3. Lower presser foot and hold thread tails.
  4. Start sewing slowly, then increase speed as needed.
  5. Use reverse lever to reinforce beginning and end of seams.
  6. Raise needle and presser foot to remove fabric.
  7. Cut threads using built-in thread cutter.

Special Functions: Drop feed for free-motion quilting, 4-step buttonhole creation, zipper installation, gathering fabric.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

  1. Clean lint from bobbin area after each project.
  2. Oil machine according to lubrication points diagram.
  3. Change needles regularly (every 8-10 hours of sewing).
  4. Check belt tension periodically.
  5. Clean exterior with soft, dry cloth only.

CAUTION! Unplug machine before cleaning or maintenance. Use only sewing machine oil.

Safety Information

Always follow safety guidelines to prevent injury and damage:

WARNING! Never operate with damaged power cord or foot controller.

Troubleshooting

SymptomPossible CauseCorrective Action
Machine won't startPower connectionCheck power cord; ensure foot controller is plugged in; check power switch.
Thread breakingTension/needleCheck threading; adjust tension; change needle; check for rough spots.
Skip stitchesNeedle/threadChange needle; ensure proper needle type; check thread quality.
Bobbin issuesWinding/insertionRewind bobbin evenly; ensure bobbin inserted correctly.
Uneven stitchesTension/fabricAdjust thread tension; use proper presser foot; check fabric feed.
Machine noisyLint/lubricationClean lint from bobbin area; oil machine; check for loose parts.
Fabric not feedingFeed dogsEnsure feed dogs are raised; check presser foot pressure.

Service: Contact authorized Janome service center for repairs. Customer support: 1-800-631-0183

Janome Sewing Machine Manual 1008 © - All Rights Reserved 2025