Bernina 700 Sewing Machine Manual

The Bernina 700 is a premium sewing machine featuring advanced stitching capabilities, computerized functions, automatic thread tension, built-in stitches, embroidery options, LCD display, needle threader, speed control, and various presser feet. Powered by standard household electrical outlet. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Setup 3. First-Time Operation 4. Technical Specifications 5. Controls and Functions 6. Stitch Selection 7. Threading & Bobbin 8. Maintenance & Cleaning 9. Accessories 10. Warranty Information 11. Troubleshooting

Features at a Glance

Key components: LCD display, stitch selection dial, thread cutter, bobbin winding system, presser foot lever, feed dogs, needle position buttons.

Feature	Description
LCD Display	Shows stitch patterns and settings
Automatic Needle Threader	Easy threading assistance
Built-in Stitches	Over 200 stitch patterns including decorative and utility
Speed Control Slider	Adjustable sewing speed
Bobbin System	Top-loading bobbin with clear cover
Presser Feet	Multiple interchangeable feet included
Thread Tension	Automatic tension control
Needle Position	Programmable up/down position
Stitch Length/Width	Adjustable settings
Memory Function	Stores favorite stitch combinations

Installation & Setup

Unpack and inspect all components. Place on stable sewing table.

Remove packaging materials and protective covers.
Install foot controller: Plug into machine port.
Connect power: Plug machine into electrical outlet.
Install needle: Loosen needle clamp screw, insert needle with flat side to back.
Wind bobbin: Follow bobbin winding instructions.

WARNING! Keep fingers away from needle area during operation. Always turn off when not in use.

First-Time Operation

Power on machine; familiarize with basic functions.

Thread machine: Follow threading path indicated on machine.
Insert bobbin: Place bobbin in case with thread pulling counterclockwise.
Select stitch: Turn stitch selection dial to desired pattern.
Adjust settings: Set stitch length and width as needed.
Test sew: Use scrap fabric to test stitch quality.

CAUTION! Always use proper needle for fabric type. Replace dull or bent needles immediately.

Technical Specifications

Stitch Capacity: 200+ built-in stitches
Maximum Stitch Width: 7mm
Maximum Stitch Length: 5mm
Speed: Up to 850 stitches per minute
Display: LCD screen with stitch preview
Bobbin: Top-loading, class 15
Needle System: HAx1 standard
Presser Feet: 8 included standard feet
Power Requirements: 110-120V, 60Hz
Weight: 22 lbs (10 kg)

Controls and Functions

Access functions via control panel and dials. Front Panel: Power switch, stitch selection dial, LCD display, reverse stitch button.

Control Panel: Stitch pattern buttons, stitch length/width adjustment, needle position, thread cutter, speed control slider.

Basic Operations: Select stitch pattern, adjust length/width, set needle position, engage reverse stitching, control sewing speed. Advanced Functions: Memory storage, automatic thread tension, built-in needle threader, programmable stitch sequences.

Stitch Selection

Over 200 built-in stitches including utility, decorative, and stretch stitches.

Turn stitch selection dial to choose category.
Use arrow buttons to select specific stitch pattern.
Adjust stitch length (0-5mm) for different fabrics.
Adjust stitch width (0-7mm) for decorative effects.
Save favorite combinations to memory.

Tip: Test stitches on scrap fabric before sewing project.

Threading & Bobbin

Proper threading ensures optimal stitch quality.

Raise presser foot and needle to highest position.
Follow numbered threading path on machine.
Use automatic needle threader for easy threading.
Wind bobbin: Place thread on spool pin, guide through tension disk.
Insert bobbin: Drop into case with thread pulling counterclockwise.
Pull bobbin thread up through needle plate.

WARNING! Always thread with presser foot raised to engage tension disks.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

Clean lint from bobbin area after each project.
Oil moving parts as indicated in manual (if required).
Wipe exterior with soft, dry cloth.
Replace needle regularly (every 8-10 hours of sewing).
Store covered when not in use.

CAUTION! Unplug machine before cleaning or maintenance.

Accessories

Standard accessories included with Bernina 700.

Accessory	Purpose
All-purpose Foot	General sewing
Zipper Foot	Installing zippers
Buttonhole Foot	Automatic buttonholes
Blind Hem Foot	Invisible hemming
Overedge Foot	Preventing fraying
Quilting Foot	Quilting projects
Embroidery Foot	Decorative stitching
Seam Ripper	Removing stitches
Brush & Screwdriver	Cleaning and adjustments
Extra Bobbins	Additional bobbins

Warranty Information

Bernina 700 comes with limited warranty covering manufacturing defects. Warranty period: 20 years for mechanical parts, 10 years for electronic components, 2 years for labor. Registration required within 30 days of purchase. For warranty service, contact authorized Bernina dealer. Keep original receipt as proof of purchase.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Thread breaking	Incorrect threading/tension	Re-thread machine; check tension settings; replace needle.
Skip stitches	Wrong needle/damaged needle	Replace needle; ensure correct needle for fabric type.
Bobbin thread bunching	Incorrect bobbin insertion	Remove and reinsert bobbin; check threading path.
Machine not feeding	Feed dogs lowered	Raise feed dogs; clean feed dog area.
Uneven stitches	Tension issues	Adjust thread tension; re-thread both upper and lower threads.
Machine not powering on	Power connection	Check power cord; ensure outlet is working; check foot controller connection.
Unusual noise	Lint buildup/mechanical issue	Clean bobbin area; check for obstructions; contact service.

Service: Contact authorized Bernina dealer for technical support and repairs.

Support: 1-800-BERNINA; www.bernina.com