Baby Lock Companion 2400 Sewing Machine Manual

The Baby Lock Companion 2400 is a computerized sewing machine with advanced features including 240 built-in stitches, automatic needle threader, drop-in bobbin system, LCD screen display, speed control slider, built-in needle plate, knee lifter compatibility, and multiple presser feet options. Designed for both beginners and experienced sewers, it offers easy operation with professional results. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: LCD display, automatic needle threader, drop-in bobbin system, stitch selection dial, speed control slider, presser foot lever, hand wheel, power switch, and foot pedal connector.

Installation & Setup

Unpack and inspect all components. Place on stable sewing table.

1. Remove packaging materials and protective covers from machine.
2. Position machine on flat, stable surface with adequate lighting.
3. Connect foot pedal to machine and plug into power outlet.
4. Install needle properly with flat side facing back.
5. Wind and insert bobbin following drop-in bobbin instructions.
6. Thread upper thread using automatic needle threader.

WARNING! Keep fingers away from needle area during operation. Always turn off power when threading or changing needles.

First-Time Operation

Power on machine; familiarize yourself with basic controls.

1. Turn power switch to ON position; LCD screen will illuminate.
2. Select basic straight stitch using stitch selection dial.
3. Practice threading with automatic needle threader.
4. Insert bobbin and pull up bobbin thread.
5. Place fabric under presser foot and lower presser foot lever.
6. Gently press foot pedal to begin sewing.
7. Adjust speed using speed control slider as needed.

CAUTION! Always use proper needle for fabric type. Test stitches on scrap fabric first.

Specifications

• Stitch Capacity: 240 built-in stitches
• Stitch Width: Up to 7mm
• Stitch Length: Up to 5mm
• Needle Positions: Adjustable left, center, right
• Bobbin: Class 15 transparent bobbin
• Speed: Up to 850 stitches per minute
• Display: LCD screen with stitch information
• Automatic Features: Needle threader, thread cutter, tension
• Power Requirements: 110-120V, 60Hz
• Machine Weight: 22.5 lbs (10.2 kg)

Controls and Settings

Access functions via LCD screen and control buttons. Front Panel: Power switch, stitch selection dial, reverse stitch button, needle up/down button, automatic thread cutter.

LCD Display: Shows selected stitch number, recommended presser foot, stitch width and length settings, needle position.

Stitch Settings: Adjust width (0-7mm), length (0-5mm), needle position (left/center/right). Utility Settings: Reverse stitch, mirror imaging, twin needle capability, memory function for custom combinations.

Stitch Selection & Functions

240 built-in stitches including utility, decorative, heirloom, and quilting stitches.

1. Turn stitch selection dial to choose stitch category.
2. Use +/- buttons to select specific stitch pattern.
3. Adjust stitch width and length as needed for fabric.
4. Select appropriate presser foot for chosen stitch.
5. Use reverse stitch button to reinforce beginnings and ends.
6. Engage mirror imaging for symmetrical decorative stitches.
7. Save custom stitch combinations to memory function.

Tip: Refer to stitch guide for recommended settings for different fabric types.

Threading & Bobbin

Automatic needle threader and drop-in bobbin system for easy operation.

1. Raise presser foot and raise needle to highest position.
2. Follow numbered threading path on machine.
3. Use automatic needle threader: Lower lever and hook thread through needle eye.
4. Wind bobbin: Place thread on spool pin, wind following bobbin winding diagram.
5. Insert bobbin: Drop bobbin into case with thread rotating counter-clockwise.
6. Pull thread through slot and under tension spring.
7. Pull up bobbin thread by holding upper thread and turning hand wheel.

WARNING! Always turn power off when threading needle or changing bobbin.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. Unplug machine before cleaning or maintenance.
2. Remove needle plate and clean lint buildup with brush.
3. Clean bobbin area and race hook regularly.
4. Oil machine according to lubrication points diagram (if required).
5. Wipe exterior with soft, dry cloth.
6. Store machine with cover when not in use.

CAUTION! Do not use compressed air for cleaning. Never oil without consulting manual.

Accessories Included

Standard accessories provided with Baby Lock Companion 2400:

• All-purpose foot
• Zipper foot
• Buttonhole foot
• Blind hem foot
• Overcasting foot
• Quilting foot
• Walking foot
• Seam ripper/lint brush
• Extra needles (various sizes)
• Bobbin (4 additional)
• Screwdriver
• Power cord and foot control
• Hard cover

Warranty Information

Baby Lock Companion 2400 comes with limited warranty: 25 years on mechanical parts, 2 years on electrical components, 1 year labor. Warranty valid for original purchaser with proof of purchase. Does not cover damage from misuse, improper maintenance, or unauthorized repairs. For warranty service, contact authorized Baby Lock dealer.

Troubleshooting

Reset: Turn machine off and on to reset computer functions.

Service: Contact authorized Baby Lock dealer for technical support and repairs.