Athena 2000 Sewing Machine Manual

The Athena 2000 is a versatile computerized sewing machine with 200 built-in stitches, automatic needle threader, LCD display, adjustable sewing speed, built-in needle plate, drop feed for free-motion sewing, automatic thread cutter, and multiple presser feet. Powered by 120V AC, 60Hz. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Accessories 7. Basic Sewing Operations 8. Advanced Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: LCD display, stitch selection dial, automatic needle threader, thread tension dial, presser foot lever, bobbin winder, speed control slider.

Feature	Description
LCD Display	Shows selected stitch, stitch length, and width settings
Automatic Needle Threader	Easy threading with push-button mechanism
Stitch Selection Dial	Select from 200 built-in stitches
Speed Control Slider	Adjust sewing speed from slow to fast
Automatic Thread Cutter	One-touch thread cutting
Drop Feed	Lower feed dogs for free-motion sewing
Bobbin Winder	Automatic bobbin winding system
Presser Foot Lever	Raises and lowers presser foot
Thread Tension Dial	Adjusts upper thread tension
Reverse Stitch Button	Reinforces stitching at beginning and end

Installation

Unpack and inspect contents. Place on stable surface.

Remove packaging materials and protective covers.
Place machine on sturdy table or sewing cabinet.
Connect foot pedal to machine port.
Plug power cord into machine and wall outlet.
Install needle and thread machine.

WARNING! Keep fingers away from needle area during operation. Always turn off machine when threading or changing accessories.

First-Time Setup

Power on machine; follow initial setup procedure.

Install needle: Loosen needle clamp screw, insert needle with flat side to back, tighten screw.
Wind bobbin: Place thread on spool pin, guide thread through bobbin winder tension, press foot pedal.
Thread machine: Follow numbered threading guide on machine.
Insert bobbin: Place bobbin in case with thread pulling counterclockwise.
Select first stitch: Turn dial to straight stitch for initial testing.

CAUTION! Ensure machine is unplugged during needle installation and threading.

Specifications

Stitches: 200 built-in stitches including utility, decorative, and stretch
Stitch Length: Adjustable 0-5mm
Stitch Width: Adjustable 0-7mm
Speed: Up to 850 stitches per minute
Needle Positions: Left, center, right
Presser Feet: 8 included (zigzag, zipper, buttonhole, etc.)
Bobbin: Front-loading, class 15 transparent
Display: LCD with stitch information
Power Source: 120V AC, 60Hz
Weight: 15.4 lbs (7 kg)

Controls and Settings

Access functions via control panel and dials. Front Panel: Power switch, stitch selection dial, reverse stitch button, thread cutter button.

LCD Display: Shows selected stitch number, stitch length, stitch width, and recommended presser foot.

Stitch Selection: Turn dial to choose from 200 stitches. Stitch Length: Adjust with length dial (0-5mm). Stitch Width: Adjust with width dial (0-7mm). Thread Tension: Adjust dial for different fabrics. Speed Control: Slide to set maximum sewing speed.

Connecting Accessories

Presser Feet: Lower presser foot lever, align foot with bar, lower lever to lock. Bobbin: Insert with thread pulling counterclockwise. Needles: Use system 130/705 H needles.

Turn off machine before changing accessories.
Match presser foot to selected stitch type.
Ensure needle is properly installed and tightened.
Check bobbin thread tension before sewing.

Tip: Always use genuine Athena accessories for optimal performance.

Basic Sewing Operations

Supports straight stitch, zigzag, buttonholes, and decorative stitches.

Select stitch: Turn dial to desired stitch number.
Set length/width: Adjust dials for fabric type.
Position fabric: Lower presser foot, begin sewing.
Reverse stitch: Press reverse button to secure ends.
Cut threads: Press automatic thread cutter or use manual cutter.
Change stitches: Stop machine, select new stitch, continue sewing.
Adjust speed: Use foot pedal pressure or speed control slider.
Finish sewing: Raise needle, lift presser foot, remove fabric.

WARNING! Never pull fabric while sewing; let feed dogs move fabric naturally.

Advanced Features

Automatic Buttonhole: One-step buttonhole with sensor. Needle Threader: Push lever for automatic threading. Memory Function: Stores frequently used stitch combinations. Mirror Imaging: Creates symmetrical decorative stitches.

Care & Maintenance

Unplug before cleaning. Remove lint from bobbin area regularly. Oil moving parts as instructed in manual.

CAUTION! Use only sewing machine oil. Do not use household oils. Clean exterior with dry cloth only.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © 2006 Athena Sewing Machines; trademarks of Athena Corporation. For support, visit www.athenasewing.com or contact 1-800-555-1234.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Machine won't start	Power connection	Check power cord connection; ensure foot pedal is plugged in.
Thread breaking	Tension/needle	Check thread tension; replace needle; rethread machine.
Uneven stitches	Threading/bobbin	Rethread upper and lower threads; check bobbin installation.
Needle breaks	Wrong needle/bent needle	Use correct needle type; replace bent needle; check fabric thickness.
Fabric not feeding	Feed dogs lowered	Raise feed dogs; clean feed dog area; check presser foot pressure.

Reset: Turn machine off and on to reset computer functions.

Service: 1-800-555-1234; www.athenasewing.com